Yocan Cylo Wax Vaporizer Manual

Charging the Yocan Cyclo Vaporizer

1. Take a USB Type-C charging cable and connect it to the port located at the bottom or base of the Yocan Cyclo Vaporizer.
2. Take the other end of the charging cable and connect it to a power brick, and then plug it into a wall socket.

Note: Alternatively, you may connect the charging cable to a desktop, laptop, or a compatible game console to recharge the Yocan Cyclo Vaporizer. The charging port is located on the bottom part of the device, just right under the “+” and “-” buttons.

Preparing the Yocan Cyclo Vaporizer

1. Make sure to fully charge the Yocan Cyclo Vaporizer to get the best results.
2. After making sure that the battery is fully charged, hit the power button five times quickly to power on the Yocan Cyclo Vaporizer.

Note: The power button is the square button located right below the atomizer base and just above the thin-film transistor (TFT) screen. You may check the battery level of the Yocan Cyclo Vaporizer through the same TFT screen.

Loading the Yocan Cyclo Vaporizer

1. Prepare your wax concentrates. Place them together with the included dab tool that comes with the Yocan Cyclo Vaporizer.
2. Remove the mouthpiece by pulling it away from the magnetic atomizer base.
3. Use your dab tool to scoop up your preferred amount of wax concentrates and place it on top of the C4-DE Plus Coil.
4. You may replace the mouthpiece by sliding it back in pace and waiting for the magnetic links to lock in place.

Note: Avoid removing the mouthpiece or the coil while the said parts are still hot. It can affect the integrity of the components and it might cause minor burns on your finger.

Removing the Coil of the Yocan Cyclo Vaporizer

1. Make sure that the Yocan Cyclo Vaporizer is powered off and has cooled down.
2. Remove the mouthpiece.
3. Twist the coil counterclockwise to loosen it from the base.
4. Take a brand-new coil (the Yocan Cyclo Vaporizer has an extra coil in the packaging) and screw it in clockwise.
5. Place the mouthpiece back on top of the base.

Note: The Yocan Cyclo Vaporizer comes with two coils, one is attached in the device and the other is a replacement for when the attached coil is used up.

Vaping with the Yocan Cyclo Vaporizer

1. Make sure that you have fully charged the battery of the Yocan Cyclo Vaporizer, installed your coil correctly, and loaded the device with your preferred wax concentrates.
2. Press the power button five times quickly to activate the battery.
3. Press and hold the power button to vaporize your wax concentrates.
4. Repeat this process as necessary or until the extracts in the atomizer are consumed.

Changing the voltage level of the Yocan Cyclo Vaporizer

1. Make sure that the Yocan Cyclo Vaporizer is powered on, press the power button five times quickly if it is still powered off.
2. Press the “+” to increase the temperature level. Doing so will allow it to produce more vapor that is more potent.
3. Press the “-” to decrease the temperature level. Doing so will allow it to produce thinner vapor that is more flavorful.
4. Once you have selected your preferred temperature level, leave the buttons and the device will automatically read your selection.
5. Yocan Cyclo Vaporizer Voltage Range:
6. From 2.0 volts to 4.2 volts

Removing and Replacing the Mouthpiece of the Yocan Cyclo Vaporizer

Pull the Yocan Cyclo Vaporizer’s mouthpiece until the magnetic connection is fully severed.
Place the mouthpiece and device close together to create a magnetic connection.
Wait for the magnetic base and the mouthpiece to snap back in place.

Note: You can clean the base of the magnetic connection when you remove the mouthpiece. This will help you enjoy clean sessions.

Care and Maintenance of the Yocan Cyclo Vaporizer

1. The Yocan Cyclo Vaporizer is made with relatively few parts making it a device that’s easy to take care of. Follow the steps below on how you can clean and take care of your Yocan Cyclo Vaporizer.
2. Wipe off any dirt or residue on the Yocan Cyclo Vaporizer battery using a dry paper towel or some alcohol wipes. Continue to reassemble the vaporizer.
3. Follow the charging instructions and use the dedicated charging cable to prolong the Yocan Cyclo Vaporizer.

Note: For maintaining the coils, make sure to refrain from using any hard objects to tamper with the heating element. In the event of a damaged coil, remove it and replace it with a new one immediately.