Yocan Pandon Vaporizer Manual

Preparing the Yocan Pandon Vaporizer

1. Make sure that you fully charge your Yocan Pandon Vaporizer before use.
2. Once you have secured a full charge, turn on the vaporizer battery by tapping the power button 5 times rapidly. Note: The power button is located at the middle part of the battery facing outwards just above the Pandon logo.
3. Once the Yocan Pandon Vaporizer is turned on you can sterilize the heating elements by pressing and holding the same power button for 5 seconds for about two or three times. Note: perform sterilization during the first time you receive your Yocan Pandon Vaporizer. This will eliminate and get rid of any impurities that might have made its way to the heating chamber during the manufacturing process.
4. Once you’re done with sterilization, you can let the vaporizer sit and rest for about 2 – 3 minutes. After which, you can now load your select concentrates to your Yocan Pandon Vaporizer.

Loading the Yocan Pandon Vaporizer

1. Set your concentrates on a receptacle, a jar, or anywhere you can safely scoop or pick your concentrates upon loading.
2. Make sure you’ve prepared your Yocan Pandon Vaporizer first if it’s the first time you’re using it. Note: Follow steps for preparing the Yocan Pandon Vaporizer.
3. Pull the mouthpiece upwards to reveal the two Yocan Quartz Dual Coils (QDC).
4. Remove the coil cap on both coils by twisting it counter clockwise. Removing the mouthpiece exposes the coils that are covered with the coil cap. Note: make sure that you do not overtighten the threads as it may damage it and cause it to be loose altogether.
5. Load desired amount of concentrate onto the coils. Note: Make sure that the dab tool does not touch the coils as contact with another metal may cause the coils to break or get damaged. Simply drop the concentrates atop the QDC.
6. Replace the coil cap and tighten it by turning it clockwise.
7. Replace the mouthpiece by sliding it back in the magnetic connection.

Switching Through the Temperature Settings

1. Power the Yocan Pandon Vaporizer on by quickly pressing the power button 5 times.
2. Tap the power button 2 times rapidly to select heat settings.
3. Release the power button to allow the selected heat setting to take effect on the Yocan Hive 2.0 Vaporizer.

Below are the corresponding heat levels.

• Green Light: Low Setting
• Blue Light: Medium Setting
• White Light: High Setting

Vaping with the Yocan Pandon Vaporizer

1. Make sure that the Yocan Pandon Vaporizer is properly sterilized, fully charged, and is loaded correctly before vaping.
2. Once loaded, take the mouthpiece and press your lips against it and prepare to draw.
3. Press and hold the power button at the same time and as the Yocan Pandon Vaporizer begins making vapors, inhale and pull from the vaporizer.
4. Repeat this process as necessary or as the concentrates are fully consumed.

Care and Maintenance of the Yocan Pandon Vaporizer

The Yocan Pandon Vaporizer has few parts which make it a solid device and is likewise easy to clean and maintain. To clean your Yocan Pandon Vaporizer, follow the steps below.

1. Turn the vaporizer on. Five clicks will turn it on and five clicks turns it off.
2. Turn the Yocan Pandon Vaporizer upside down.
3. Perform a burn-off by pressing and holding the power button for 5 seconds. Repeat this process 2 – 3 times. This will cause any residue to melt or evaporate.
4. Let the vaporizer cool down.
5. Disassemble the Yocan Pandon Vaporizer by pulling the magnetic parts apart and by turning the threaded connections counter clockwise.
6. Wipe off the vaporizer and the parts with a dry paper towel and reassemble.