Yocan Rex Portable Enail Vaporizer Kit Manual

Preparing the Yocan Rex Portable Enail Vaporizer Kit

1. Fully charge your Yocan Rex’s battery for best results.  Connect the USB charging cable to a computer or a wall adapter and the USB-C tip to the vaporizer.
2. Once you have fully charged the battery, turn the Yocan Rex Portable Enail Vaporizer Kit on by pressing the power button with one long click or until the light on the vaporizer turns on.  

Note: The power button is located at the top part of the battery, it is circular in appearance and has sides that illuminate when powered on.  

Loading the Yocan Rex Portable Enail Vaporizer Kit

1. Prepare your wax concentrates. Use a wax container to keep the extracts.  
2. Access the coils by unscrewing battery from the base.
3. Carefully load the wax concentrates into the coils (you can use a dab tool).
4. Replace the battery by screwing it back in place.  
5. Setting up the Yocan Rex Portable Enail Vaporizer Kit
6. Use the Yocan Rex Portable Enail Vaporizer Kit with a 14mm bong or an 18mm water pipe.  
7. For health purposes, make sure that the water pipe is clean.  
8. Fill it with the recommended amount of water as per the water pipe manufacturer.  
9. Depending on the joint on your water piece flip the water pipe adapter to fit a male or a female joint or downstem.  
10. Make sure that the Yocan Rex Portable Enail Vaporizer Kit is seated properly and that it does not wiggle atop the water pipe.  

Vaping with the Yocan Rex Portable Enail Vaporizer Kit

1. Make sure that the Yocan Rex Portable Enail Vaporizer Kit is fully charged and is loaded with your select wax concentrates before you start vaping.  
2. After you have loaded the Yocan Rex Portable Enail Vaporizer Kit, turn the device on by giving the power button a long click.  
3. Press your lips against the mouthpiece and once it creates vapors pull and draw from the water pipe.  
4. Repeat this process after the extracts are fully vaporized or you can manually stop the Yocan Rex Portable Enail Vaporizer Kit by giving the power button a long click.
5. Changing the Temperature Level of the Yocan Rex Portable Enail Vaporizer Kit
6. Make sure that the Yocan Rex Portable Enail Vaporizer Kit is powered on.  
7. Press the power button three times rapidly to toggle through the available preset temperature levels.  

Voltage Settings:  

• Low – 3.2 volts  
• Medium – 3.7 volts  
• High – 4.2 volts  

Note: Each voltage level is also represented by a dedicated LED light setting allowing you to see the running voltage level from a distance. Low is represented by a white light, medium in blue light, and high in green light.  

Adjusting the airflow of the Yocan Rex Portable Enail Vaporizer Kit

1. When you inhale from the Yocan Rex Portable Enail Vaporizer Kit, twist the airflow vent clockwise to tighten and restrict the airflow.  
2. Otherwise, twist the airflow vent counterclockwise to loosen and allow more air to pass through.  

Care and Maintenance of the Yocan Rex Portable Enail Vaporizer Kit

1. The Yocan Rex Portable Enail Vaporizer Kit is a portable eNail that is made with few parts making it an ideal device to travel with that is likewise easy to clean and maintain. The Yocan Rex Portable Enail Vaporizer Kit is a simple and straightforward wax concentrate vaporizer and requires only a few steps to clean. To maintain your Yocan Rex Portable Enail Vaporizer Kit, follow the steps below.  
2. Wipe off any dirt or residue on the battery with a dry paper towel.
3. Disassemble the Yocan Rex Portable Enail Vaporizer Kit and separate the parts including the battery, the coil, and the water pipe adapter.  
4. The coil can be cleaned by soaking it in isopropyl alcohol for a few hours, give it a light brush, and let dry.  
5. The water pipe adapter can be cleaned with alcohol wipes and a cotton swab.  

For battery maintenance, make sure to follow charging instructions and use the dedicated charger to avoid damaging the Yocan Rex Portable Enail Vaporizer Kit battery.