Yocan UNI Pro 2.0 Box Mod Manual

Preparing the Yocan UNI Pro 2.0 Box Mod

1. Make sure to fully charge your Yocan UNI Pro 2.0 Box Mod’s battery for best results. Connect the USB charging cable to a computer or a wall adapter and the USB Type-C tip to the vaporizer (the charging port can be found on the device just below the left and right temperature adjustment buttons).
2. Once you have fully charged the battery, you can start using the Yocan UNI Pro 2.0 Box Mod by pressing the power button five times quickly.

Note: The power button of the Yocan UNI Pro 2.0 Box Mod can be found above the OLED screen. The power button is the square button on the device.

Loading the Yocan UNI Pro 2.0 Box Mod

1. Prepare your select oil cartridges.
2. If you are using a refillable cart, make sure not to overfill the cartridge with your select oils (or wax concentrates).
3. If you are using a pre-filled cartridge, just make sure that there are no obstructions on the mouthpiece of the cart.
4. Connect the cart to the magnetic ring through the 510-threaded connection.
5. Gently slide the cartridge inside the cart chamber.
6. Depending on the size of your cartridge, you may adjust the width and the height of the chamber.

Note: The Yocan UNI Pro 2.0 Box Mod uses magnetic rings to connect the cartridge to the battery. In the event that you run into some connection issues with the cartridge. Try loosening the connection and avoid overtightening the 510-threaded connection.

Vaping with the Yocan UNI Pro 2.0 Box Mod

1. Make sure that the Yocan UNI Pro 2.0 Box Mod is fully charged and that you have prepared your select oils (or wax concentrates) before you start vaping.
2. Select your preferred voltage setting by using the directional buttons located at the bottom of the OLED screen.
3. Prepare to inhale from the mouthpiece when you have decided on your preferred settings.
4. Press and hold the power button to activate the heating element.
5. Repeat this process until you are satisfied or until the oils (or wax concentrates) are fully consumed.

Changing the Temperature Level of the Yocan UNI Pro 2.0 Box Mod

1. Make sure that the Yocan UNI Pro 2.0 Box Mod is fully charged.
2. Press the left directional button to decrease the temperature level.
3. Press the right directional button to increase the temperature level.
4. When you have found the right temperature level, let go of the button and it will automatically activate the selected setting.

Voltage Settings:

• From 1.8 volts to 4.2 volts.

Note: The temperature level can be viewed on the OLED screen. It is adjusted, depending on which button you choose, in 0.1-volt increments.

Activating Pre-Heat Function

1. You can activate the Yocan UNI Pro 2.0 Box Mod’s pre-heat function by pressing the power button twice.
2. To cut off pre-heat, simply press the power button twice again.

Note: In pre-heat mode, the Yocan UNI Pro 2.0 Box Mod uses a constant low temperature level of 1.8 volts. It warms up the oil (or concentrates) without extracting its cannabinoids in the process.

Accessing On Demand Mode

1. You can access On Demand Mode by pressing and holding down the power button.
2. Lift your finger from the power button to stop On Demand Mode.

Care and Maintenance of the Yocan UNI Pro 2.0 Box Mod

The Yocan UNI Pro 2.0 Box Mod is a portable oil and wax pen that is made with few parts making it an ideal device to travel with that is likewise easy to clean and maintain. The Yocan UNI Pro 2.0 Box Mod is a simple and straightforward oil vaporizer and requires only a few steps to clean. To maintain your Yocan UNI Pro 2.0 Box Mod, follow the steps below.

1. Wipe off any dirt or residue on the battery with a dry paper towel.
2. Disassemble the Yocan UNI Pro 2.0 Box Mod and separate the removable parts.
3. For battery maintenance, make sure to follow charging instructions and use the dedicated charger to avoid damaging the Yocan UNI Pro 2.0 Box Mod battery.