Yocan Uni Pro Plus Box Mod Manual

Preparing the Yocan UNI Pro Plus Box Mod Vaporizer

Note: The power button is located at the front of the battery where you have the part where you can see the OLED screen and the “+” and the “-” buttons facing outwards. The power button is the squarish button at the front located just above the OLED screen logo.

1. Make sure that your Yocan UNI Pro Plus Box Mod Vaporizer is properly charged before you use it, for best results.
2. After the battery is charged, power the Yocan UNI Pro Plus Box Mod Vaporizer on by pressing the power button for five times rapidly.

Loading the Yocan UNI Pro Plus Box Mod Vaporizer

Note: Do not over tighten the magnetic adapter as it may cause the threads to get loose. This may cause other cartridges to experience a loose connection affecting the flow of electricity and the overall performance of the Yocan UNI Pro Plus Box Mod Vaporizer.

1. Prepare your cartridge, place it somewhere safe and where there’s a stable platform so the cartridge won’t roll over or fall off the table which may cause it to break.
2. Connect the cartridge to the 510-threaded magnetic connector.
3. Place the 510-threaded attachment from your cartridge to the receiving end of the magnetic adapter. Lightly twist the magnetic adapter until you feel resistance.
4. Once the adapter is securely connected to the cartridge, you may slide the cartridge down to the Yocan UNI Pro Plus Box Mod Vaporizer chamber until you hear a satisfactory snap.
5. Use the necessary adjustment tools on the Yocan UNI Pro Plus Box Mod Vaporizer to secure the cartridge in place. The width and the diameter of the cartridge can be adjusted to fit the chamber by twisting the aperture adjustment tool. Do this so the cartridge will not rattle and shake inside the chamber. Should your cartridge be lacking in height, the height adjustment tool can be used with three height settings. Bottom, medium, and high.

Vaping with the Yocan UNI Pro Plus Box Mod Vaporizer

1. Make sure that the Yocan UNI Pro Plus Box Mod Vaporizer is charged and is loaded with your select cartridge before you start vaping.
2. Tap the power button five times quickly to turn the device on.
3. Once the Yocan UNI Pro Plus Box Mod Vaporizer is loaded and powered on, put your lips on the mouthpiece of the cartridge and prepare to draw.
4. Press and hold the power button of the Yocan UNI Pro Plus Box Mod and once the Yocan UNI Pro Plus Box Mod Vaporizer generate vapors, you can start pulling from the mouthpiece of the cartridge.
5. Repeat this process as necessary or as the oil or wax concentrates are fully consumed.

Selecting the Temperature Setting for the Yocan UNI Pro Plus Box Mod Vaporizer

One of the main advantages of using the Yocan UNI Pro Plus Box Mod Vaporizer is its precise temperature settings.

• Simply press the left or the right button to select voltage level.

Note: The voltage level can be adjusted in 0.1-volt increments.

Selecting the Pre-heat for the Yocan UNI Pro Plus Box Mod Vaporizer

• Press the power button twice to activate pre-heat mode.

Care and Maintenance of the Yocan UNI Pro Plus Box Mod Vaporizer

The Yocan UNI Pro Plus Box Mod Vaporizer was made to accommodate a wide range of cartridges. The Yocan UNI Pro Plus Box Mod in itself is only a box mod battery with no atomizers or cartridge with it. To ensure your Yocan UNI Pro Plus Box Mod Vaporizer stays in good shape, follow the steps below.

1. Wipe-off any liquid or material residue on the vaporizer with a dry paper towel and continue with wiping the entirety of the Yocan UNI Pro Plus Box Mod Vaporizer with a dry paper towel.
2. You can also wipe the magnetic contacts to wipe off the smudges and the dirt that may cause unstable flow of electricity. For this step, you can use cotton swabs to get to the heard to reach spaces.
3. Make sure to follow charging instructions and use the dedicated charger to avoid damaging the UNI Pro Plus Box Mod battery.