Yocan Wit Box Mod Manual

Preparing the Yocan Wit Box Mod Vaporizer

1. Make sure that your Yocan Wit Box Mod is fully charged before attempting to use for ideal results.
2. After securing a fully charged battery, turn the Yocan Wit Box Mod Vaporizer on by tapping on the power button 5 times quickly. Note: The power button is located at the upper center part of the battery just right above the diamond cut marking on the center of the device. The power button is the diamond-shaped button above the larger diamond marking.

Loading the Yocan Wit Box Mod Vaporizer

1. Prepare your cartridges, make sure to place them somewhere where there’s a leveled platform so the cartridges will remain safely in place and won’t break due to accidentally falling from the table.
2. Connect your cartridge to the included 510-threaded magnetic adapter.
3. Place the 510-threaded attachment of your cartridge to meet the receiving end of the magnetic adapter. Twist the magnetic adapter until you feel slight resistance. Note: Do not over tighten the magnetic adapter as it may cause the threads to get loose. This may cause other cartridges to experience a loose connection affecting the flow of electricity and the overall performance of the Yocan Wit Box Mod Vaporizer.
4. Once the adapter is securely connected to the cartridge, you may insert the cartridge down to the Yocan Wit Box Mod Chamber until you hear a snap which means that the magnets have securely locked together.

Vaping with the Yocan Wit Box Mod Vaporizer

1. Make sure that the Yocan Wit Box Mod Vaporizer is charged and is properly loaded with your select cartridge before you start your session.
2. Make sure that the Yocan Wit Box Mod is powered on by tapping the power button 5 times quickly.
3. After you have loaded the Yocan Wit Box Mod Vaporizer, press your lips near the mouthpiece of the cartridge and prepare to inhale.
4. Press and hold the power button of the Yocan Wit Box Mod and once the Yocan Wit Box Mod Vaporizer generates vapors pull and draw from the mouthpiece of the cartridge.
5. Repeat this process as necessary or until the extracts inside the cartridge is fully consumed.

Switching Through the Temperature Settings

1. Power the Yocan Wit Box Mod Vaporizer on by clicking the power button 5 times.
2. Tap the power button three times rapidly to toggle in between temperature settings.
3. Release the power button to allow the selected heat setting to take effect on the Yocan Wit Box Mod Vaporizer.

Below are the corresponding heat settings and their respective voltage levels. Each voltage level is represented by the amount of green light that is lit on the LED panel.

• One Light: Low Setting
• Two Lights: Medium Setting
• Three Lights: High Setting

The Yocan Wit Box Mod Vaporizer is also outfitted with a 10-second preheat function. To activate the preheat setting, follow the steps below.

• Click the power button twice.
• Click the power button twice again to stop preheat.

Care and Maintenance of the Yocan Wit Box Mod Vaporizer

The Yocan Wit Box Mod Vaporizer was made to accommodate a wide variety of cartridges that measure up from 9 – 11.5 mm in diameter. The Yocan Wit Box Mod in itself is only a Box Mod with no atomizers on it and it does not come with any cartridge out of the box. To ensure your Yocan Wit Box Mod Vaporizer stays in good working condition, follow the steps below.

1. Wipe-off any liquid residue or resin from extracts on the vaporizer with a dry paper towel and continue with cleaning the Yocan Wit Box Mod Vaporizer with a dry paper towel.
2. You can also wipe the magnetic contacts to wipe off the smudges and the dirt that may cause unstable flow of electricity.
3. Make sure to follow charging instructions and use the dedicated charger to avoid damaging the Wit Box Mod.