Yocan Explore Vaporizer Manual

Preparing the Yocan Explore Vaporizer

1. Make sure that you give your Yocan Explore Vaporizer a full charge before use.
2. Once you have a fully charged battery, turn on the vaporizer by clicking on the power button 5 times. Note: The power button is the circular button located at the middle part of the battery facing outwards right above the LCD display screen.
3. After the Yocan Explore Vaporizer is powered on you can sterilize the heating element by pressing and holding the power button for 5 seconds. Do this for two or three times. Note: perform sterilization during the first time you receive your Yocan Explore Vaporizer. This will eliminate and get rid of any impurities that might have made its way to the heating chamber during the manufacturing process.
4. As soon as you’re done with sterilization, you can let the vaporizer rest and cool down for about 2 – 3 minutes. After so, you can start loading your select materials to your Yocan Explore Vaporizer.

Loading the Yocan Explore Vaporizer Wax Atomizer

1. Lay your concentrates on a piece of parchment paper, a dab mat, or a jar where you can safely scoop or pick them up when loading.
2. Make sure have finished preparing your Yocan Explore Vaporizer first. Do this especially if it’s the first time you’re using it. Note: Follow steps for preparing the Yocan Explore Vaporizer.
3. Unseat the mouthpiece from the battery.
4. Unscrew the wax concentrate chamber from the mouthpiece to gain access to the inside of the concentrate compartment.
5. Load desired amount of concentrate onto the chamber.
6. Replace the chamber by screwing it back in place connected to the mouthpiece. Note: make sure that you do not overtighten the threads as it may damage it and cause it to be loose altogether.
7. Slide the mouthpiece back to the battery.

Loading the Yocan Explore Vaporizer Herb Atomizer

1. Place your dry herbs somewhere you can easily access them without having to risk spilling them elsewhere.
2. Make sure have finished preparing your Yocan Explore Vaporizer first. Do this especially if it’s the first time you’re using it. Note: Follow steps for preparing the Yocan Explore Vaporizer.
3. Unseat the mouthpiece from the battery.
4. Unscrew the herb chamber from the mouthpiece to gain access to the inside of the herb compartment.
5. Load desired amount of dry herb materials onto the chamber.
6. Reseat the chamber by screwing it back in place connected to the mouthpiece. Note: make sure that you do not overtighten the threads as it may damage it and cause it to be loose altogether.

Vaping with the Yocan Explore Vaporizer

1. Make sure that the Yocan Explore Vaporizer is properly sterilized, fully charged, and is loaded with the correct material as per the atomizer before vaping.
2. Set the proper temperature before vaping by clicking the right button below the screen to increase the temperature and the left button below the screen to decrease the temperature.
3. Once the temperature is set, take the mouthpiece and press your lips against it and prepare to draw.
4. Press and hold the power button for 3 seconds, this will cause the temperature to blink.
5. Wait for the device to heat up. Check the display screen to see whether the temperature has already stopped blinking. Once the blinking stops, the Yocan Explore Vaporizer is ready to use.
6. Repeat this process as necessary or as the materials are fully consumed.

Care and Maintenance of the Yocan Explore Vaporizer

The Yocan Explore Vaporizer has few parts including both wax and herb atomizers. Having few parts to deal with make cleaning and maintenance swift and easy. To clean your Yocan Explore Vaporizer, follow the steps below.

1. Turn the vaporizer off. Five clicks will turn it on and five more clicks turn it off.
2. Remove the mouthpiece from the battery.
3. Take the included cleaning kit and brush any residue off from where the atomizer/mouthpiece was removed.
4. Wipe off the vaporizer and the parts with a dry paper towel and reassemble.